Changelog EvoControl Vent - MPO1
Models: Modeller syns här inom kort.
1. programme version “MPO”
EvoControl med manöverpanel “MPO”!
Set values are not changed during a software update.
2025-10-03
General:
- Internal improvements.
New:
- Estonian language introduced.
Bugs:
- Network bug regarding static IP fixed.
2025-04-01
General:
- Internal improvements.
New:
- Parameter (5220) inserted that can be activated in case of network loss to do an automatic software restart.
- Parameter (482) Rotormotionering ändrad till “Default PÅ”
2024-10-30
General:
- Internal improvements.
Bugs:
- An A alarm does not stop the unit unless “Emergency = On”.
2024-10-22
General:
- Internal improvements.
- Delay in software reset so that values can be safely stored away at restart.
- Adjustment of response time for Modbus reading.
New:
- New parameter id for “Timer” (Id 8000->) and “Alarm / Alarm history” (Id 9000->).
- Obs: Nya parameter Id för “Tidur” och “Larm / Larmhistorik”, berör de som använder Modbus!
Bugs:
- Hysteresis for free cooling.
2024-05-13
General:
- Internal improvements.
- Improved handling of missed communication to e.g. display and stepper motor.
2024-03-19
General:
- Internal improvements.
- Re-initialises Modbus if the connection is broken incorrectly.
- Better control of display parameters.
New:
- Can have preheaters even when you have “Mixed signal” as post-heating.
Bugs:
- The EVB time may show the wrong time after a power cut.
2024-01-15
General:
- Obs: Programversion DUC visar fel årtal! Programversion DUC visar “M 2023-01-15:1” men är “M 2024-01-15:1”. Programversion Display visar “D 2024-01-15:1” (rätt).
- Internal improvements.
New:
- Exercise run of heat exchanger (rotor), parameter 482.
- Knapplås infört.
- Går ställa av EvoCloud även när nätverket är aktiverat.
2023-12-01
General:
- Internal improvements.
Bugs:
- Attendance hours counted down minutes instead of hours.
- When changing the priority order of external inputs, the operating mode could stay in the higher priority mode, e.g. “External 2”. Can be fixed by selecting “Last input” and then selecting new “Operational” and then setting back to “Priority”. Also applies to “External Stop” and “Fire”
2023-08-07
General:
- Internal improvements.
New:
- When defrosting, the rotor runs with control signal 78%.
- More models of stepper motor for rotor drive added.
- New function for presence sensor, switch-off delay.
Bugs:
- When returning from overpressure/forcing timer and an external input has been active, the unit can go to stop.
2022-11-30
General:
- Internal improvements.
New:
- Improved rotor control and alarm management.
- Going to switch off rotor test.
- Indication is made if the rotor stops when it is below zero outside before the rotor test alarm.
- Displays text for operating mode extra at rotor text.
- Increased running time of stepper motor in rotor control.
Bugs:
- In case of slave control of fans (pressure & flow), the fans were not switched at supply air fan position down.
2022-09-21
General:
- Internal improvements.
New:
- Displays “Start-up” in the control panel before both fans have started during hot start.
- Improved rotor control and alarm management.
Bugs:
- None.
2022-09-05
General:
- Internal improvements.
New:
- Cooling acceleration, the fans increase steplessly according to the cooling rate.
- Cooling recovery even in free cooling.
Bugs:
- Rotor test (VVX) can be done at low rotor control signals (rotor attempts to start).
2022-07-04
General:
- Internal improvements.
New:
- Split priority order for external inputs (parameters 470-472), Save-External 2 (terminals 1-6) / Stop (terminals 7-8) / Fire (9-10).
- Moved parameter number 472 to 475 (motor type).
Bugs:
- None.
2022-06-09
General:
- Internal improvements.
New:
- Förbättrad reglering av frysskydd och frikyla vid vattenbatteri.
Bugs:
- None.
2022-05-17
General:
- Internal improvements.
New:
- Förbättrad reglering av frysskydd och varmhållning vid vattenbatteri.
Bugs:
- None.
2022-05-10
General:
- Internal improvements.
New:
- Nivån för rotorlarm (VVX) höjd till minst 20% styrsignal.
- Förbered att använda stegmotor.
Bugs:
- None.
2022-04-01
General:
- Internal improvements.
New:
- Fläkt kapacitets begränsning.
- Möjlighet till ersättningsfläktar med annan varvtals mätning.
- Omdirigering av EvoCloud.
Bugs:
- Under uppdatering och fuktgivare ansluten blev det larm från fuktgivaren.
2021-12-21
General:
- Första versionen.
Your feedback helps us to develop our documentation.