⚠️ The website is under development. Subject to compatibility issues and possible typographical errors.
English (UK)
English (UK)
EvoDry Pro dehumidifiers are delivered on pallets and can be handled carefully with a forklift as long as the protective packaging is intact.
Acetec AB is not responsible for damages that occur as a result of incorrect installation or incorrect handling and which may cause damage to persons or property.
Acetec AB is not liable for damage or consequential damage arising from failure to follow the instructions given or from failure to use and maintain the product for its intended purpose.
Changes to the product may not be made without written authorisation from Acetec AB.
Acetec AB reserves the right to change the product design, technical data and associated documentation without prior notice.
EvoDry 120 Pro is a desiccant dehumidifier developed for professional and industrial environments where continuous and controlled humidity management is required. The unit is suitable for business-critical spaces where stable humidity is essential to ensure the operation, function and protection of equipment and installations.
Characteristics
Full product information is available at www.acetec.se
EvoDry dehumidifiers are manufactured and quality assured in Älvsbyn, Sweden.
| Specification | Value |
|---|---|
| Suitable up to (m³) | 3500 |
| Control equipment | EvoControl Touch |
| Wet air flow (m³/h) | 175 |
| Dry air flow rate (m³/h) | 1000 |
| Capacity at 20°C/60% RF (l/24h) | 108 |
| Sound level (dBA) | 47 |
| Hedging (A) | 16 |
| Power, fan, nom (W) | 170 |
| Power, at dehumidification (W/h) | 6100 |
| W x H x D (mm) | 616 / 665 / 985 |
| Weight (kg) | 59 |
For technical advice or to request a quote, please contact sales@acetec.se
| Designation | Dimensions (mm) |
|---|---|
| A | 985 |
| B | 665 |
| C | 616 |
| D | 308 |
| E | 416 |
| F | 314 |
| G | 205 |
| H | 20-40 |
| D1 | 160 |
| D2 | 250 |
See designations in the illustration above.
The humid air is removed from the serviced area and the system can be used at temperatures below 0 °C.
The process air to be dehumidified passes through the filter, fan and sorption rotor and then leaves the dehumidifier as dry air.
The air used to dry the slowly rotating sorption rotor is called regeneration air. It passes through the filter, fan, regeneration heater, sorption rotor and leaves the dehumidifier as warm and moist humid air, which is led out of the served area.
The regeneration air can be taken in as outdoor air, which creates neutral pressure in the served space. If the regeneration air is instead taken directly from the space where the dehumidifier is located, negative pressure is created corresponding to the amount of wet air that is removed.
EvoDry Pro has inspection hatches on both sides and can therefore be installed in right-hand and left-hand versions.
In front of the unit's inspection hatch, there must be a free space corresponding to the width of the unit. This is necessary so that the filter and all components can be replaced during servicing.
Free space that should be available in front of the inspection hatch:
| Unit | Min. service space (mm) | Recommended service space (mm) |
|---|---|---|
| EvoDry 30 Pro | 460 | 1000 |
| EvoDry 60 Pro | 530 | 1000 |
| EvoDry 120 Pro | 630 | 1200 |
| EvoDry 180 Pro | 720 | 1200 |
If the air duct is connected to an exterior wall (outdoors), the intake must be placed high enough to prevent dust, debris, rain and snow from being sucked in. For this purpose, a wall fitting adapted to the respective dehumidifier size is used. Place the wall fitting away from contaminants, such as exhaust fumes. It should also be placed at least 2 metres from the wet gas outlet.
If wall diffusers are not used, the intake opening must be equipped with precipitation protection and a small animal-proof net (mesh size 10×10 mm). Fresh air can also be taken from the served space; in such cases, the fresh air intake must be equipped with a small animal-proof net. When return air is taken from the served space, a negative pressure corresponding to the amount of wet air is created.
Wet gas is always vented through an exterior wall (outdoors) using the shortest possible duct. The duct must be corrosion-resistant and able to withstand temperatures of up to approximately 100 °C. It must be insulated on the outside if there is a risk of condensation in the duct. The duct must also be installed with a downward slope from the dehumidifier, and a condensation hole (6 mm) should be drilled at the lowest point of the duct to prevent water accumulation. Check the appropriate location of the condensation hole so that the small amount of condensation water that is drained does not risk causing damage.
Wall outlets for wet gas (accessories) must be installed at least 2 metres from any wall outlets for rainwater. Consider the outdoor environment so that the location does not cause discomfort to the surroundings. If wall outlets (accessories) are not used, the wet gas outlet must be fitted with precipitation protection and a small animal-proof net (mesh size 10×10 mm).
The EvoDry Pro sorption dehumidifier is factory-calibrated to provide maximum dehumidification capacity and high energy efficiency. Normally, no adjustments are necessary.
The capacity for process and control air flow is specified in the technical data for each model. Air flows are measured on the suction side, i.e. on the process and control air side.
When changing settings, the following table values should be taken into account for optimal performance:
| Unit | 30 Pro | 60 Pro | 120 Pro | 180 Pro |
|---|---|---|---|---|
| Maximum total power, W | 2000 | 2800 | 6100 | 10600 |
| Maximum total current, A per phase | 9 | 12 | 9 | 15 |
| Process air flow, m³/h, min – max | 100 - 260 | 200 - 500 | 400 - 1000 | 800 - 2100 |
| Air flow, m³/h, min – max | 25 - 70 | 50 - 120 | 70 - 180 | 120 - 300 |
| Ratio, %, recommended reg/process air flow | 28 | 25 | 18 | 24 |
Control is via a 4.3-inch colour panel with touch display, providing a clear and intuitive user experience. The system has a wired network connection for stable communication and also offers a cloud solution with a responsive design that automatically adapts to mobile phones, tablets or computers. Advanced functionality allows you to control the indoor climate with high precision, customise operation as needed and monitor the system in real time.
EvoControl Touch consists of the following parts:
The touch panel should be installed in a warm, weather-protected and dry area where it is clearly visible and easily accessible to the user. Avoid placing it in areas with high humidity or risk of condensation.
Would you like a more detailed description with pictures? Click on the link or scan the QR code at the top. See section 6.
This quick guide applies to standard professional dehumidifiers without accessories. For complete technical instructions, use the link on the first page of the manual or scan the QR code.
Press the button Menu: 
Press the button Preferences: 
Enter authorisation code 6374 (8990 for advanced) and press Enter.
See Step 5 on the next page.
Press the button Moisture: 
Press the button Operation: 
Select capacity mode: Low, Between, High or car.
Acetec products are carefully designed for long operating life, high reliability and easy maintenance. Follow the instructions below and keep a spare filter handy for the next filter change. Normal service and maintenance consists of filter replacement and internal cleaning. The service alarm can be activated in programming mode, and the service reminder interval can be set – see the section on settings and programming mode.
The unit must be disposed of in accordance with applicable environmental legislation. Contact your local environmental authorities for information on correct sorting and handling.
The sorption rotor material is non-combustible and should be sorted as glass fibre. If there is any suspicion that the rotor has been exposed to an unhealthy or contaminated environment, a risk assessment should be carried out. Environmentally hazardous substances and chemicals may be stored in the rotor material.
Take appropriate measures to comply with environmental legislation and local regulations.
See AG20 warranty for full terms and conditions.
| Date | Performed by | Listing |
|---|---|---|
| Specification | Value |
|---|---|
| Terms and conditions of guarantee | AG20 |
| EC | Yes |
| Dehumidification type | Sorption |
| Working range (°C) | -20 to +40 |
| Suitable up to (m³) | 3500 |
| Control equipment | EvoControl Touch |
| Cloud service | Yes |
| Wet slurry flow (m³/h) | 175 |
| Wet end (mm) | 160 |
| Dry air blast (mm) | 250 |
| Dry air flow (m³/h) | 1000 |
| Capacity at 20°C/60% RF (l/24h) | 108 |
| Capacity up to (l/24h) | 108 |
| Sound level (dBA) | 47 |
| Hygrostat setting (%) | 20 to 80 |
| Power, fan, nom (W) | 170 |
| Dehumidification power (W/h) | 6100 |
| Connection voltage (V) | 3 × 400 |
| Hedging (A) | 16 |
| IP class | IP21 |
| W x H x D (mm) | 616 / 665 / 985 |
| Weight (kg) | 59 |
| Filter class | M5 |
| Coatings / Materials | Magnelis |
| Corrosion class | C4 |
Svenska Svenska English (UK)
Deutsch
Dansk
Norsk bokmål
Íslenska
Suomi
Eesti
Latviešu valoda
Lietuvių kalba
